Tiger-Vac SS-10 (4W) SK HEPA
Air-powered ATEX vacuum for Zone 1 and Zone 21, built to extract dust directly at a pneumatic sander. Supplied with suction and air hose, air supply hose, wye connector and multimeter, so you can connect your own sander. HEPA H14, AISI 304 stainless steel and room for two operators on the same machine.
- Extracts dust at the sander, where it is generated
- Air-powered, so there are no electrical parts in the machine
- ATEX temperature class T6, max. 85°C surface temperature
- Up to two operators on the same machine
- For your own pneumatic sander, supplied with air through the vacuum
- ATEX Directive 2014/34/EU: II 2GD Ex h IIC T6 Gb / Ex h IIIC T85°C Db
- LCIE 03 ATEX 6310 X (third-party certificate)
- IECEx LCIE 17.0076 X
- EN 17348 DT for combustible dust collection
- EN 1822 and IEST-RP-CC001 for HEPA H14
- EN ISO 11203 for sound pressure measurement
Tiger-Vac SS-10 (4W) SK HEPA
Tiger-Vac SS-10 (4W) SK HEPA is an air-powered ATEX vacuum built to work with a pneumatic sander in hazardous areas. The dust is extracted at the sander, where it is generated, instead of settling in the area, where it can be stirred up again and form an explosive dust cloud. Tiger-Vac is phasing out its own sanders, so the set is supplied without a sander and you connect your own. Tell us the size of the dust extraction port on your sander, and together with Tiger-Vac we will make sure the setup fits.
The sander gets its air through the vacuum. Compressed air runs from the compressor to the machine in one air hose, and from there on to the sander in a combined suction and air hose with a protective sleeve. Suction is created by a single 6 mm venturi, and the vacuum has neither electrical parts nor moving mechanical parts. It is therefore certified in ATEX temperature class T6 with a maximum surface temperature of 85°C and marked II 2GD for Zone 1 gas and Zone 21 dust. The certification covers the vacuum; the sander needs its own documentation for the zone it is used in.
The vacuum is dual-certified under ATEX (LCIE 03 ATEX 6310 X) and IECEx (LCIE 17.0076 X) and marked EN 17348 DT for combustible dust collection. It is built for dry recovery into a 19 litre disposable filter bag, followed by a static dissipative main cloth filter and a HEPA H14 filter. The whole machine is AISI 304 stainless steel, resistance to earth is below 10 ohm, and it stands on a 4-wheel dolly with static dissipative wheels.
Up to two operators can work simultaneously on the same machine. The wye connector has two hose shanks, so two sanders can be connected. The suction and air hose, air supply hose, wye connector and multimeter are the same as Tiger-Vac supplied with its sanding kits.
Applications
- Sanding steel and metal surfaces before painting in areas classified as Zone 1 or Zone 21
- Maintenance of coatings on tanks, pipework and process plant in the chemical and petrochemical industry
- Sanding where the sanding dust itself is combustible, for example paint, lacquer and powder coating
- Sites where compressed air is easy to bring in, but an approved electrical installation is not
- Work where dust must be captured at source for the sake of the working environment
Technical specifications
| ATEX marking (vacuum) | II 2GD Ex h IIC T6 Gb / Ex h IIIC T85°C Db · LCIE 03 ATEX 6310 X · IECEx LCIE 17.0076 X · EN 17348 DT |
|---|---|
| Internal / external zone | No internal zone. External Zone 21 for dust and Zone 1 for gas |
| Drive | Pneumatic venturi, single 6 mm nozzle, no electrical components |
| Sander | Not included. Your own pneumatic sander gets its air through the vacuum |
| Temperature class | T6, max. 85°C surface temperature |
| Ambient temperature | -4°C to +37°C |
| Airflow | 204 m³/h |
| Vacuum | 448 mbar (4,570 mmH₂O) |
| Air consumption, vacuum | 21.2 L/s (1,272 Nl/min) |
| Supply pressure | 5.5 bar |
| Compressed air connection | Ø 12.7 mm (1/2") |
| Minimum compressor | 15 to 25 HP |
| Sound pressure | 79 dB(A) to EN ISO 11203 |
| Filter class | H class |
| Filter type | HEPA H14 with 99.995 % efficiency at 0.3 µm, tested to IEST-RP-CC001 and MPPS to EN 1822, aerosol leak tested at the factory |
| Primary filter | Static dissipative main cloth filter on a stainless steel cage |
| Filter cleaning | None, manual |
| Recovery | Dry recovery only |
| Filter bag | Disposable filter bag, 19 L |
| Material | AISI 304 stainless steel |
| Resistance to earth | Below 10 ohm |
| Suction inlet | Ø 50 mm |
| Cart | 4-wheel dolly (4W) with static dissipative wheels |
| Operators | Up to 2 simultaneously |
| Hose connections for sander | 2 × 1.25" (32 mm) on the wye connector, the suction and air hose ends in 1" |
| Part numbers | Vacuum 110263 · wye connector 501503 · suction and air hose 303020D · air supply hose 211030 · multimeter 211065B |
What is included
Everything below is included. A sander is not included; you use your own. Hoses and filters are static conductive or static dissipative, so the ESD chain is unbroken.
Tiger-Vac
HEPA filter H14 (211027B)
99.995 % efficiency at 0.3 µm. Tiger-Vac aerosol leak tests all HEPA systems before they leave the factory. Included.
Tiger-Vac
Main cloth filter, static dissipative (211013A)
Takes most of the dust before the air reaches the HEPA filter. Fitted on a stainless steel cage (212734). Included.
Tiger-Vac
Disposable filter bag, 19 L
Collects the sanding dust. Conductive collection bags with a 64 mm collar (212994-SD64, pack of 3) and a 40 L conductive poly liner with drawstring (212100S) are also included.
Tiger-Vac
Air supply hose, 1/2" × 15 m (211030)
Carries compressed air from the compressor to the machine. Static dissipative, with a quick disconnect at each end. Included.
Tiger-Vac
Suction and air hose (303020D)
Static conductive and crushproof. Extracts dust from the sander and carries air to it. 30 feet in total (25 feet of 1.25" and 5 feet of 1") with a 6 foot protective sleeve. Included.
Tiger-Vac
Wye connector (501503)
Aluminium, 2" (50 mm) female camlock to the machine and two 1.25" (32 mm) hose shanks for the sanders, with one plug. Included.
Tiger-Vac
Multimeter (211065B)
For measuring resistance to earth in the ESD chain. Included.
- Your own sander: Tiger-Vac is phasing out its own sanders. Tell us the size of the dust extraction port on your sander, and we will make sure the hose fits.
- 4-wheel dolly (4W): With static dissipative wheels, so the cart is part of the ESD chain.
- AISI 304 stainless steel: The whole machine, with resistance to earth below 10 ohm.
Questions and answers
Is a sander included?
No. Tiger-Vac is phasing out its own sanders and recommends using your own pneumatic sander. The set is supplied with the vacuum, suction and air hose, air supply hose, wye connector and multimeter. Tell us the size of the dust extraction port on your sander, and together with Tiger-Vac we will make sure the setup fits.
How does the sander get its air?
Through the vacuum. Compressed air runs from the compressor to the machine in the supplied 1/2" air hose of 15 metres, and from the machine on to the sander in the combined suction and air hose. The same hose carries the dust back from the sander to the machine. Only one air hose has to be run from the compressor.
How many people can sand at the same time?
Up to two operators can work simultaneously on the same machine. The supplied wye connector has two 1.25" (32 mm) hose shanks and comes with one plug.
What compressor does the SS-10 SK need?
Tiger-Vac specifies a compressor of at least 15 to 25 HP, 5.5 bar supply pressure and a 1/2" (12.7 mm) air line. The vacuum uses 21.2 L/s (1,272 Nl/min), and the sander's own air consumption comes on top. Contact us and we will work out the total air consumption for the sanders you plan to run. Remember that the compressor is itself an ignition source and must stand outside the classified zone.
What does the marking II 2GD Ex h IIC T6 Gb mean?
II means equipment group II, i.e. everything except mines. 2GD is category 2 for both gas and dust, which corresponds to external Zone 1 for gas and Zone 21 for dust. Category 2 does not cover the inside of the equipment, i.e. Zone 0 and Zone 20, which requires category 1. Ex h is the type of protection for non-electrical equipment under EN ISO 80079-36. IIC is the most demanding gas group and also covers hydrogen and acetylene. T6 is the most demanding temperature class with a maximum surface temperature of 85°C, and Gb is the equipment protection level for gas corresponding to category 2.
What does the ATEX certificate cover?
The certificates LCIE 03 ATEX 6310 X and IECEx LCIE 17.0076 X cover the vacuum itself, a venturi vacuum with no electrical and no moving mechanical parts. The X means specific conditions of use: the machine must be earthed according to the manufacturer's instructions, and only accessories recommended by the manufacturer may be used. The sander is not covered and needs its own documentation for the zone it is used in.
Can the machine pick up liquids?
No. The SS-10 (4W) SK HEPA is built for dry recovery. If you also need to pick up liquids, look at the SS-10 (4W) RE HEPA (MRAC), which handles both wet and dry.
What is included?
HEPA H14 filter, static dissipative main cloth filter with stainless steel cage, 19 L disposable filter bag, conductive collection bags and a 40 L conductive poly liner. Also the combined suction and air hose (303020D), a 15 m air supply hose (211030), a wye connector for two sanders (501503) and a multimeter for measuring resistance to earth (211065B). A sander is not included.
